We all know the warning signs about clogging and sewage problems, the way the sink sinks or the water circulates and falls off your feet in the bathroom, and pungent and foul smells are all signs you may be clogged soon. You face the sewage and one day you will see that the waterway is completely closed, so act immediately.
Well, you cleaned the excess hair, greasy and sticky stuff on the surface of the sewer, nothing happened, now you try to act like a plumber but in vain, but what happens when the blockage does not open? Or should we say what can we do to open these clogs faster? In the continuation of this section, we will suggest 10 solutions with a specific effect for opening the sewer pipe in this case.
Hassle-free solutions for opening sewer pipes in the bathroom and dishwasher
Here are ten solutions you can try before resorting to the perfect and expensive method of notifying the plumber.
1. A long, curved (spring) wire to open the sewer pipe:
Very simple, but oddly useful, take a metal clothespin to which the suit is attached and smooth the bend well, then bend one side at the end in the form of a small hook. Throw it into the water and think you are fishing, try to get rid of all the hair, grease and lumps of dirt. Remember to try to pull the contents of the tube, not push it further and push it down. When you pull out the contents as much as possible, pour enough hot water into the water, this way you can easily open the tube. May be.
2. Open the sewer pipe using salt and vinegar:
Make a mixture of one-third cup of salt and one-third cup of vinegar; Due to the combination of the two, gas is emitted from it. Pour the mixture into the sewer without wasting time and before the boiling is over. Boiling this mixture will clean the hair, grease and the contents of the tube. Let the water stay the same for about an hour. Then wash the tube with warm water and high pressure. You can also pour enough salt into the tube first and then pour the vinegar on it.
3. Dry and wet vacuum cleaner Sewer opening solution:
If you have a dry and wet vacuum cleaner, know that it is a great tool for opening the drain, first set it on the suction of liquids, cover its outlet to prevent dirty work, then seal the pipe well around, you may want a Use an old bag for this purpose By turning on the high-power vacuum cleaner, the vacuum cleaner pulls all the contents that caused the clogging into the bag. This does not always work, but it is worth testing.
4. Open the sewer pipe with boiled water:
This is no easier task, put the kettle on the stove or in the microwave and pour as much water as it can and boil it. Now gently pour it into the tube in two or three steps. Let some hot water. Run every second and then pour the next series of water. This is always the easiest and fastest solution. If the pipe opens before the boiling water runs out, congratulate yourself and make yourself a cup of tea with the rest.
5. Open the sewer pipe with salt ink :
Wear plastic gloves and eye protection, salt ink can cause sharp and unpleasant burns. You can get it from your local hardware store, but be very careful when transporting it. Pour 3/4 gallon of cold water into the bucket and add 3 cups of salt ink to it. Mix it well with an old wooden spoon. The mixture starts to boil and emits gas and heat. Pour the solution into the sewer and between 20 to 30 Give it a minute. Then rinse the tube with hot water and repeat if necessary.
6. Open the sewer pipe by draining the well:
There are jobs that drain the well, but we can not do that, but there is a simple task, first put an empty bucket under the U-shaped sewer pipe, use the wrench to collect water in the pipe, and Loosen the washers at the two ends of the pipe under the sink. You should try to hold all the components of the pipe by hand. When the clamps are opened, release it and return it to the bucket and pour all the contents of the pipe into the bucket. It may be necessary to rotate the inside of the tube with something and clean up any remaining debris. Do this for both sides of the tube. An old, broken toothbrush is a good tool for this. Rinse the joints with water. And clean and close again. Most of the time this trick will work.
7. Open the sewer pipe through the elbow pipe:
This is a piece of water pipe, at the bottom of which has a special code work. It is basically a flexible metal tube with a spiral shape at the end. The following video shows you what to do.
8. Salt and baking soda home method of opening the sewer pipe:
Combine 1/2 cup kitchen salt with 1/2 cup baking soda and pour it into the clogged drain. Allow to stand for 20 minutes, then pour boiling water over it. Hot water and salt and baking soda will form a chemical compound. Which dissolves a large part of the masses and fats in the sewage.
9. Open the sewer pipe with dishwashing detergent:
If your toilet water is blocked, pour 1/4 cup of dishwashing liquid into the bowl, then boil it with some water. The detergent acts as a lubricant and cleans the residue in the sewer, then pour enough hot water into the waterway. If the pipe still does not open, it is time to wear plastic gloves.
10. Open the sewer pipe with baking soda and vinegar:
If you take a bath tube, mix some baking soda and vinegar and pour it in two steps and then give it time. Wait about 45 to 60 minutes. Now fill the tub with hot water. Now remove the lid of the tub at once and with Direct 45 to 60 gallons of water into the waterway The pressure from the water and the impact of the materials you have already poured into the pipes will help open the waterway.
More tutorials:
https://mrplumber.ir/qeytarieh-plumbing/
