The first step is to put the case together. The motherboard, graphics card, microprocessor, main memory, hard drive, and network interface card are all standoffs that keep the motherboard in place during installation. A few connections to the motherboard will also be required.The motherboard and microprocessor chip must be removed from their packaging. One corner of the chip will be marked, and that corner must line up with a matching corner on the motherboard's socket. Align both corners of the microprocessor before inserting it into its socket. As long as everything is aligned perfectly, there should be no need to exert any pressure. Once you've got it in, use the lever arm to tighten it up. Installing the heat sink is the next step. You'll find instructions in the CPU box's handbook. Depending on the model, the heat sink will include either a heat sink sticker or heat sink grease. You only had to put the heat sink in place, secure it with flanges on both sides, then secure it with a cam to install it. Essay writing Services of Academic Master is providing help to world wide people in their works for increasing performance.Connect the heat sink's power supply to the motherboard using this cable.Once you've decided on the type of RAM you want, it's time to put it in your computer. RAM should be handled with caution. The motherboard houses the computer's RAM slots. Typically, there are two spots available, however this can vary. The RAM may require more force than you expect to secure it in place. In addition, a rotating arm on each side of the module should be used to inspect the RAM from above.It's time to stow away your motherboard in the case. The back connectors on your motherboard should be covered by a faceplate that came with the motherboard. You must insert the plate and press it into place until it clicks. To prevent any of its connectors from coming into contact with the case, it should be placed about a quarter of an inch away from the surface. Find the screws needed to install the motherboard in the case. Don't overtighten the screws. When screwing in the screws, be extremely careful. There is a risk of damaging the motherboard's small wires if you drop them into the casing.This includes putting in the HDD and DVD-ROM drives. Four rubber grommets on a detachable bracket on the case align with four holes in the hard drive. Grommet-punching screws were also included in this package. Screw the hard drive back into its bracket and into the case. Make sure the jumpers are set correctly if you are utilising IDE/PATA drives. To power the hard drive, connect it to the power supply using one of the power supply's connectors. The cables are now ready to be installed. The cable features a red stripe on one side, which signifies "pin 1" on the connector. The cable should be plugged into the "1" IDE port on the motherboard. The other end of the cable should be inserted into the drive's back panel. The drive is now operational.The CD-ROM drive will now be installed. Set the jumpers up correctly once more. You may need to remove a faceplate to create room for the CD-ROM drive in the front of the case. Make sure it's lined with the front of the case before screwing it in. You can attach the power supply to any accessible connector, just like you did with the hard drive. Connect the CD-ROM drive to the motherboard using the included cable, then plug the other end into the drive. Connect the CD player's audio. On the motherboard and on the drive itself, there is an obvious spot for it to be plugged in.A ribbon cable is used to connect hard disc drives to each other. All the wires of a ribbon cable are laid out on top of each other, rather than bundled or wrapped together. There are either 40 or 80 wires in IDE ribbon cables. Each end of the cable has a connector, as well as one roughly two-thirds of the way to the motherboard connector. Each one of the three connectors has a distinct colour and connects to various things:
The motherboard is connected to the blue connector.
The primary (master) drive is connected to the black connector.
The secondary (slave) drive is attached to the grey connector.
Putting in the power supply is the final step. In the power supply, there are two components. The fan is on the exterior of the casing, and the wires are on the inside. Screw the power supply into place on the brackets provided. Connect the motherboard's power connector. There should be two of these, one huge and one little, and it should be clear where each belongs. You'll have roughly 15 more wires to deal with. There is a page in the instructions that tells you exactly where each component goes. It's easy to tell which port each of them belongs to because they're all labelled the same. Turn on your machines and see if they're working. Assuming there is one, check to see if it is turned on. In addition, make certain that the power supply is configured to 110 or 220 volts as required.
